search Site Search

How To Do If The Shower Is Blocked Again? Do Not Rush! Use It To Soak … A Miracle! Hurry To Tell Your Customers!

ClassificationBlog 17432 0

Bathroom Business School 2020-11-24

Shower, we use every day. But have you found that the showerhead used for a period of time is full of spots of yellow scale? This not only looks very dirty but also affects the water coming out of the shower. Whether it is wiped with a rag or brush, after a lot of effort, the scale is still difficult to clean. At this point, what to do? Do not rush! Next bathroom girl teach you a few simple methods ~

0 4 1

 

The Shower Head Is Clogged, The Solution Trick.

The shower head will be clogged after a long period of use. This is very natural. This does not mean that the shower head is broken, do not worry, there is absolutely no need to buy a new one. This is mainly due to the limescale that occurs after a long period of water discharge. You just need to disassemble the shower head for cleaning.

1、After a long time of water discharge, it is difficult for some granular objects in the inlet pipe or tap water to come out from the outlet hole, and it will be easy to block the outlet hole. Remove the shower head and gently shake the water inlet toward the bottom to pour out the debris inside. Take care to save the accessories when dismantling the nozzle.

640 3

2, choose a container that can put down the nozzle, pour in white vinegar, toilet bowl cleaner or special limescale cleaner, a weak acid. Put the nozzle into the end of the water soak for a period of time (1 hour is appropriate), use a small toothbrush or other clean brush to brush, and then put the water to rinse.

640 4 1

3, after the water rinse, wipe clean with a rag around the water hole and the surface of the scale. Meet the more “stubborn” deposits, do not use a needle. Scrape with a fingernail until it falls off, and then clean with a rag.

640 5

 

Shower Maintenance Methods

1, the use of ambient temperature should not exceed 70 degrees Celsius. High temperature and ultraviolet light will greatly accelerate the aging of the shower, shorten the service life of the shower, so the installation of the shower as far away as possible from the bath and other electrical heat sources. Shower can not be installed in the bath bar directly below, and the distance should be more than 60CM.

2, in the area of hard water quality, please try to use the shower with rubber particles or with a straight clean device. Even if the shower outlet hole is clogged with scale, it is easier to clean. Remember not to forcibly disassemble the shower. Because of the complex internal structure of the shower, non-professional forced disassembly will lead to the shower can not be restored to its original state.

3, open and close the shower faucet and adjust the shower water way do not force too hard, gently turn the homeopath. Even the traditional faucet, also do not need to spend a lot of power. Pay special attention not to the faucet handle, shower bracket as a handrail to support or use.

640 1 1

4, the shower head metal hose should be kept in a natural stretch state, do not coil it on the faucet when not in use. At the same time, pay attention to the joint of the hose and faucet do not form a dead end, so as not to break or damage the hose.

5, every six months or less, the shower will be removed and placed in a small basin. Pour and soak the surface and inside of the shower with edible white vinegar for 4-6 hours, then gently wipe the surface of the shower at the spout with a cotton rag. Reinstall the connector and pass water for a moment, and wait for the white vinegar and scale to flow out with the water, in order to eliminate or reduce the influence of scale on the shower, and can bring some sterilization effect.

640 6 1

 

Shower Cleaning Tips

1, wall-mounted shower faucets are generally more prominent, so be careful not to bump or press it when you put items. Avoid contact with rings and other hard objects as much as possible to avoid fatal injuries.

2, the ideal cleaning technique is to rinse the faucet with water, and then wipe dry all the water on the metal surface of the faucet with a soft cotton cloth, because the water will form scale on the metal surface after evaporation. Gently wipe, do not vigorously rub. Dry with moistened sponge and soft leather, can make the faucet luster and shine.

640 7 1

3, such as the need for a lot of cleaning work, it is best to use mild liquid glass cleaner, or non-acid, non-abrasive soft liquid and completely dissolved powder, non-frictional solution polish can remove the faucet on the coarse solid mask and buildup. Do not use any abrasive cleaners, cloths or paper cloths, and any acid-containing cleaners, polishing rubbers or rough cleaners. When cleaning is complete, remove all detergent with water and blot dry with a soft cotton cloth.

Previous:: Next:

您好!Please sign in

Click to cancel reply
    展开更多
    Welcome to the WOWOW FAUCET official website

    loading...

    Select your currency
    USDUnited States (US) dollar
    EUR Euro

    Cart

    X

    Browsing History

    X